AL3226-1613AC-HL
AL3226-1613AC-HL Pelican Hardigg

Model #: AL3226-1613

Available Colors

Configuration: Classic

PLEASE NOTE: Pelican-Hardigg Single Lid cases shown may include optional, non-standard configurations that require additional specification and cost. Please contact Pelican Customer Service to discuss available configurations.

Commercial Quote Locate an Authorized Dealer Near You.
Product Features
  • One-piece construction, molded from lightweight, high-impact polyethylene
  • Molded-in ribs and corrugations for secure, non-slip stacking, columnar strength, and added protection
  • Patented molded-in metal inserts for catch and hinge attachment points, which provide strength and spread loads to the container
  • Positive anti-shear locks, which prevent lid separation after impact, and reduce stress on hardware
  • Molded-in, tongue-in-groove gasketed parting lines for splash resistance and tight seals, even after impact
  • Reinforced corners and edges for additional impact protection
  • Recessed hardware for extra protection

Overview

PELICAN HARDIGG/ SINGLE-LID STANDARD COLORS
STD Grey 133
Fed Std #26270
STD Tan 250
Fed Std #20372
Blue 135
Pantone #292U
STD White 132
Fed Std #27925
STD Yellow 136
Pantone #012U
STD Green 138 - Forest
Fed Std #24052
Orange 134
Fed Std #12197
STD Yellow 131
Fed Std #23538
Maroon 197
Pantone #202U
STD Blue 101
Fed Std #25052
STD Black-032
Fed Std #27040
Red 130
Fed Std #21105
STD Olive Drab-137
Fed Std #34096
Purple-129
Pantone #245U



Specs

Dimensions
Interior (L×W×D)
32.50 x 26.62 x 29.02"
Exterior (L×W×D)
35.50 x 29.62 x 33.21"
Measurements
Lid Depth
12.90"
Bottom Depth
16.12"
Total Depth
29.02"
Int Volume
14.5 ft³
Weights
Weight
62.50lbs
Materials
Body Material
RotoMolded Polyethylene
Latch Material
Steel (Nickel-black Plated)
Optional Hardware
136
O-Ring Material
Silicone Sponge
Purge Body Material
Aluminum
Hardware Material
134
Temperatures
Minimum Temperature
-20°F
Maximum Temperature
140°F
Warranty
Warranty Period
1 Year Material and Workmanship
Testing
Pelican-Hardigg Single Lid style roto cases have been designed and tested to meet or exceed the applicable requirements of the following standards. Qualification is conducted through direct testing and/or engineering analysis of product and test similarity; testing has been conducted on containers of various sizes and configurations as applicable.
  • MIL-STD-810E, Method 505.3, Procedure II – SOLAR RADIATION
  • ASTM E96, MIL-C-4150J and ASTM D 1008-64 – WATER-VAPOR TRANSMISSION RATE (PERMIABILITY)
  • FED SPECIFICATION L-P-390c, Type M. – TENSILE/ELONGATION/COMPRESSIVE/FLEXURAL
  • FED-STD-101, Method 5009 – LEAK TEST
  • FED-STD-101, Method 5016 & DOT 49CFR 178.350 – CONCENTRATED LOAD (STACK/SUPERIMPOSED)
  • FED-STD-101, Method 5011 – HANDLING
  • MIL-STD-810E, Method 514.4 – VIBRATION (COMPOSITE INPUTS)
  • MIL-STD-810E, Method 516.4, Procedure IV – SHOCK (TRANSIT DROP)
  • MIL-STD-810E, Method 501.3, Procedure I – TEMPERATURE (STORAGE, HIGH TEMPERATURE)
  • MIL-STD-810E, Method 502.3, Procedure I – TEMPERATURE (STORAGE, LOW TEMPERATURE)
  • MIL-STD-810E, Method 507.3, Procedure I – RELATIVE HUMIDITY
  • MIL-STD-810E, Method 500.3 – ALTITUDE (LOW PRESSURE)
  • MIL-STD-210C & MIL-STD-810D, Method 510.2, Procedure I – SAND AND DUST
  • MIL-STD-810E, Method 509.3, Procedure I @ 5% – SALT FOG
  • MIL-STD-810D, Method 508.4 – FUNGUS
  • MIL-STD-810D, Method 506.2, Procedure I – RAIN WITH WIND
  • MIL-STD-810D, Method 512.2, Procedure I – IMMERSION ONE (1) METER
  • ATA 300, Category I – REQUIREMENTS FOR REUSABLE CONTAINERS

Support

guarantee
For warranty information, see our
Guarantee of Excellence
support
For additional support,
contact us