AL2727-1409AC
AL2727-1409AC Single Lid Case

Part#: AL2727-1409

Available Colors

Configuration: Classic

Commercial Quote Locate an Authorized Dealer Near You.
Product Features
  • One-piece construction, molded from lightweight, high-impact polyethylene
  • Molded-in ribs and corrugations for secure, non-slip stacking, columnar strength, and added protection
  • Patented molded-in metal inserts for catch and hinge attachment points, which provide strength and spread loads to the container
  • Positive anti-shear locks, which prevent lid separation after impact, and reduce stress on hardware
  • Molded-in, tongue-in-groove gasketed parting lines for splash resistance and tight seals, even after impact
  • Reinforced corners and edges for additional impact protection
  • Recessed hardware for extra protection

Overview

Trusted for over 40 years by the US Military, Single Lid Cases offer 20% more protective material in the edges and corners, where it is needed most, ensuring that valuable equipment is kept safe from any unforeseen elements. Available in several sizes, these cases are completely customizable with a wide range of bolt-on options like document holders, casters, humidity indicators and much more.
PELICAN HARDIGG/ SINGLE-LID STANDARD COLORS
STD Grey 133
Fed Std #26270
STD Tan 250
Fed Std #20372
Blue 135
Pantone #292U
STD White 132
Fed Std #27925
STD Yellow 136
Pantone #012U
STD Green 138 - Forest
Fed Std #24052
Orange 134
Fed Std #12197
STD Yellow 131
Fed Std #23538
Maroon 197
Pantone #202U
STD Blue 101
Fed Std #25052
STD Black-032
Fed Std #27040
Red 130
Fed Std #21105
STD Olive Drab-137
Fed Std #34096
Purple-129
Pantone #245U



Specs

Dimensions
Interior (L×W×D)
27.00 x 27.00 x 23.37"
Exterior (L×W×D)
30.00 x 30.00 x 25.56"
Measurements
Lid Depth
9.25"
Bottom Depth
14.12"
Total Depth
23.37"
Int Volume
9.9 ft³
Weights
Weight
41.10lbs
Materials
Body Material
RotoMolded Polyethylene
Latch Material
Steel (Nickel-black Plated)
O-Ring Material
Silicone Sponge
Purge Body Material
Aluminum
Hardware Material
134
Temperatures
Minimum Temperature
-20°F
Maximum Temperature
140°F
Testing

Pelican-Hardigg Single Lid style roto cases have been designed and tested to meet or exceed the applicable requirements of the following standards. Qualification is conducted through direct testing and/or engineering analysis of product and test similarity; testing has been conducted on containers of various sizes and configurations as applicable.

  • MIL-STD-810E, Method 505.3, Procedure II - SOLAR RADIATION
  • ASTM E96, MIL-C-4150J and ASTM D 1008-64 – WATER-VAPOR TRANSMISSION RATE (PERMIABILITY)
  • FED SPECIFICATION L-P-390c, Type M. - TENSILE/ELONGATION/COMPRESSIVE/FLEXURAL
  • FED-STD-101, Method 5009 – LEAK TEST
  • FED-STD-101, Method 5016 & DOT 49CFR 178.350 – CONCENTRATED LOAD (STACK/SUPERIMPOSED)
  • FED-STD-101, Method 5011 – HANDLING
  • MIL-STD-810E, Method 514.4 – VIBRATION (COMPOSITE INPUTS)
  • MIL-STD-810E, Method 516.4, procedure IV – SHOCK (TRANSIT DROP)
  • MIL-STD-810E, Method 501.3, procedure I – TEMPERATURE (STORAGE, HIGH TEMPERATURE)
  • MIL-STD-810E, Method 502.3, procedure I – TEMPERATURE (STORAGE, LOW TEMPERATURE)
  • MIL-STD-810E, Method 507.3, Procedure I – RELATIVE HUMIDITY
  • MIL-STD-810E, Method 500.3 – ALTITUDE (LOW PRESSURE)
  • MIL-STD-210C & MIL-STD-810D, Method 510.2, Procedure I – SAND AND DUST
  • MIL-STD-810E, Method 509.3, Procedure I @ 5% – SALT FOG
  • MIL-STD-810D, Method 508.4 – FUNGUS
  • MIL-STD-810D, Method 506.2, Procedure I – RAIN WITH WIND
  • MIL-STD-810D, Method 512.2, Procedure I – IMMERSION ONE (1) METER
  • ATA 300, Category I – REQUIRMENTS FOR REUSABLE CONTAINERS

Support

guarantee
For warranty information, see our
Guarantee of Excellence
support
For additional support,
contact us